| 1 | External negative-insert holder with top or lever clamping | General-purpose external turning, facing, and heavier cuts where a robust insert is suitable. | Match the insert shape, size, thickness, nose radius, and hand to the holder designation. Confirm the clamping system and that the turret accepts the shank size. | A firm insert seat and secure clamp support stable cutting. Check clearance around the workpiece, chuck, and turret before selecting the holder hand and approach angle. | Keep the insert seat and clamp clean and undamaged. Index or replace inserts when cutting edges wear, chip, or no longer meet the required finish. |
| 2 | External positive-insert holder with screw clamping | Finishing and lighter cuts, including applications where lower cutting forces are useful. | Confirm the positive insert’s shape, size, thickness, screw-hole arrangement, and orientation match the holder. Use the specified clamping screw and seating parts. | Positive geometry can reduce cutting forces, but the insert and clamp must be fully seated. Avoid excessive tool projection, especially on small or less rigid setups. | Inspect the screw, insert pocket, and cutting edge regularly. Replace damaged screws or seats; do not compensate for a loose fit by overtightening. |
| 3 | Steel-shank boring bar | Internal turning and boring in holes with adequate room for the bar and chip flow. | Check bar diameter against the minimum bore, and confirm the insert code, hand, clamping method, and required boring depth. | Keep overhang as short as the job allows and clamp the bar securely. Steel bars are commonly selected for shorter overhangs; vibration risk rises as unsupported length increases. | Use cutting conditions appropriate to the bar’s reach and material. Check the bar for wear, damage, and built-up material, and maintain a sharp, correctly seated insert. |
| 4 | Carbide-shank boring bar | Internal turning where a longer overhang or greater resistance to deflection than a comparable steel bar is needed. | Verify bar diameter, minimum bore, insert and screw specifications, machine clamping method, and clearance throughout the bore. | Carbide is stiffer than steel of the same dimensions but is less tolerant of impact and mishandling. Use a secure clamp and avoid sudden shocks or interrupted cuts beyond the bar’s capability. | Prevent chipping from impact, poor alignment, or unstable cutting. Inspect the bar and insert seat for cracks or damage and follow the tool maker’s handling guidance. |
| 5 | External grooving and parting blade holder | Cutting grooves or separating parts from bar stock. | Match blade width, height, length, insert system, and holder pocket. Check required groove width, cut depth, machine clearance, and workpiece diameter. | Set the blade at the correct center height and square to the workpiece. Minimize blade projection and ensure the workpiece and setup are well supported. | Maintain a clear chip path and use suitable coolant where applicable. Replace chipped inserts and inspect blade pockets and clamping surfaces for wear. |
| 6 | Internal grooving holder or grooving bar | Making grooves, reliefs, or recesses inside a bore. | Check the bar diameter against the bore, along with groove width, required depth, insert width, and the holder’s minimum-bore limits. | Use the largest bar that fits with adequate clearance and keep its overhang short. Confirm that the holder will not contact the bore wall during entry or withdrawal. | Control chip evacuation to reduce recutting and edge damage. Inspect the insert, pocket, and bar for wear, especially after deep or narrow grooving operations. |
| 7 | External threading holder | Cutting external threads with a single-point threading insert. | Match the insert profile and pitch range to the thread standard and required form. Confirm insert hand, holder hand, seat orientation, and clearance at the shoulder. | Seat the insert securely and align it correctly to the work axis. A rigid setup helps reduce chatter and maintain thread-form consistency over repeated passes. | Use an edge and cutting setup suited to the work material. Check the cutting edge and insert alignment if the thread finish or profile begins to deteriorate. |
| 8 | Internal threading bar | Cutting threads inside a bore where a single-point threading tool can reach the feature. | Verify the bar fits the minimum bore and reaches the thread length. Match insert profile and pitch to the thread, and check the required hand and internal clearance. | Minimize overhang and ensure the bar is firmly clamped. Confirm there is room for chip evacuation and for safe entry and exit from the thread. | Monitor insert-edge wear and chip control. A damaged edge or unstable bar can affect thread form and surface finish; inspect the bar and insert seat between jobs. |
| 9 | Profiling and copy-turning holder | Contouring shoulders, radii, tapers, and other shaped external or internal features. | Check insert shape, nose radius, cutting direction, and clearance against the workpiece profile. Confirm the insert can reach the full contour without holder interference. | Choose a holder and insert orientation that provide clearance without excessive overhang. Complex contours may require checking for interference along the complete tool path. | Use a suitable insert geometry for the material and contour. Inspect the edge when the profile finish changes, and avoid allowing the holder or insert to rub on the finished surface. |
| 10 | Modular-interface turning holder | Applications requiring interchangeable heads or repeatable tool setup across compatible machine interfaces. | Confirm the interface standard, size, locking method, holder orientation, and machine-side connection all match. Also verify insert compatibility at the cutting head. | Clean mating faces before assembly and tighten the connection as specified. Interface condition and secure locking are essential to repeatability and cutting stability. | Protect locating faces and locking features from chips, corrosion, and impact. Inspect mating surfaces and locking components regularly, and replace worn parts as needed. |